Search found 142 matches
- Thu Oct 10, 2013 8:03 am
- Forum: Problems / Questions
- Topic: WATER PUMP SEALANT, GASKET OR BOTH?
- Replies: 2
- Views: 2554
Re: WATER PUMP SEALANT, GASKET OR BOTH?
It's a 1.6 16v by the way k4m 782 .
- Thu Oct 10, 2013 7:59 am
- Forum: Problems / Questions
- Topic: WATER PUMP SEALANT, GASKET OR BOTH?
- Replies: 2
- Views: 2554
WATER PUMP SEALANT, GASKET OR BOTH?
Hi,
Renault state that when replacing water pump to apply a bead of Loctite 518 gasketing product, however my water pump has come with a gasket , my question is do you have to use both or, is Loctite used when no gasket is available ?
Thanks.
Renault state that when replacing water pump to apply a bead of Loctite 518 gasketing product, however my water pump has come with a gasket , my question is do you have to use both or, is Loctite used when no gasket is available ?
Thanks.
- Fri Sep 27, 2013 8:59 pm
- Forum: Problems / Questions
- Topic: Gearbox Reverse Switch - question on change ? ? ?
- Replies: 4
- Views: 3160
Re: Gearbox Reverse Switch - question on change ? ? ?
There will be a good bit of oil comes out so act as quick as you can , I done my scenic reverse switch 2 weeks ago and when I took the switch out it was like taking a drain plug out , get a drip tray .
- Fri Sep 13, 2013 7:31 am
- Forum: Problems / Questions
- Topic: Scenic II dash
- Replies: 2
- Views: 1838
Scenic II dash
Hi folks, I recently purchased a scenic II for next to nothing, the dash had failed in 2010 and was replaced by a new unit (date on unit is 8/12/10). I have noticed a problem with it being that, when the electronic handbrake is engaged/disengaged there is supposed to be a message on dash which says ...
- Mon Aug 26, 2013 3:26 am
- Forum: Problems / Questions
- Topic: Heater Blower controls not working
- Replies: 1
- Views: 1426
Re: Heater Blower controls not working
Hi there , I had to end up replacing the blower motor myself , I thought it was the resistor also but it wasn't.
- Mon Aug 26, 2013 3:18 am
- Forum: Problems / Questions
- Topic: DIFFERENT WINDOW PROBLEM AFTER FIX
- Replies: 0
- Views: 1057
DIFFERENT WINDOW PROBLEM AFTER FIX
Hi Folks,
I recently repaired my passenger side window with new module and calibrated it , works fine apart from when you put it down it stops about an inch from bottom and then goes into trip mode again until you re - calibrate it, anyone ever experienced this after repair ?
Adam
I recently repaired my passenger side window with new module and calibrated it , works fine apart from when you put it down it stops about an inch from bottom and then goes into trip mode again until you re - calibrate it, anyone ever experienced this after repair ?
Adam
- Sun Aug 25, 2013 8:19 pm
- Forum: Problems / Questions
- Topic: K4M TIMING BELT REPLACEMENT
- Replies: 8
- Views: 9854
Re: K4M TIMING BELT REPLACEMENT
Hi Alex,
Thanks for the reply , I totally understand now and, I'll certainly be using the procedure by the manual, it was actually the Haynes manual I was reading . Regards to the pulley bolts , the kit comes with new ones. And yes it wouldn't do any harm to mark things I suppose. Thanks.
Adam.
Thanks for the reply , I totally understand now and, I'll certainly be using the procedure by the manual, it was actually the Haynes manual I was reading . Regards to the pulley bolts , the kit comes with new ones. And yes it wouldn't do any harm to mark things I suppose. Thanks.
Adam.
- Fri Aug 23, 2013 2:05 pm
- Forum: Problems / Questions
- Topic: K4M TIMING BELT REPLACEMENT
- Replies: 8
- Views: 9854
K4M TIMING BELT REPLACEMENT
Hi Folks, I will soon be doing a cambelt change on the 1.6vvt K4M engine, I am confident I can do it and have the tools ( and patience ) however, one thing which is confusing me in the manual is where it states : ''Before loosening the crankshaft pulley bolt note that the crankshaft sprocket isn't k...
- Tue Jun 18, 2013 2:47 pm
- Forum: Problems / Questions
- Topic: Help Please - Window Motor
- Replies: 3
- Views: 2290
Re: Help Please - Window Motor
Hi, the temic control module on the motor is more than likely damaged due to water ingress.
- Tue Jun 18, 2013 2:44 pm
- Forum: Problems / Questions
- Topic: AIR CON QUESTION
- Replies: 0
- Views: 1030
AIR CON QUESTION
If your air con system needs re-gassed , would the compressor still kick in when turned on ? Whenever I turn mine on it does nothing, no change in revs or engine tone.
Thanks.
Thanks.
- Tue Jun 18, 2013 2:40 pm
- Forum: Problems / Questions
- Topic: Anti Roll Bar Bushes.
- Replies: 7
- Views: 8110
Re: Anti Roll Bar Bushes.
Hi guys, It was the passenger side drop link, replaced and running smooth. Can't believe the mot missed it . The ball actually popped out of the joint when I pulled it off. I'm glad it wasn't the bushings on the roll bar itself cause I wasn't looking forward to dropping the sub frame!!
- Sun Jun 16, 2013 4:17 pm
- Forum: Problems / Questions
- Topic: Anti Roll Bar Bushes.
- Replies: 7
- Views: 8110
Re: Anti Roll Bar Bushes.
Thanks guys for your help, I will investigate during the week and post back on my findings . Thanks.
- Sun Jun 16, 2013 12:28 pm
- Forum: Problems / Questions
- Topic: Anti Roll Bar Bushes.
- Replies: 7
- Views: 8110
Re: Anti Roll Bar Bushes.
Hi Alex, it seems that there is no such procedure for removing the bushes by themselves but one for removing the complete anti-roll bar, i'm only guessing my problem , have a knocking/rattling noise from passenger side on uneven roads or going over bumps only at low speed, funny thing is It just pas...
- Sat Jun 15, 2013 1:37 pm
- Forum: Problems / Questions
- Topic: Anti Roll Bar Bushes.
- Replies: 7
- Views: 8110
Anti Roll Bar Bushes.
Hi everyone, I am looking to change the inner bushes on my anti roll bar, can this be done without dropping the sub frame? I can see the bolts that hold the clip on to them and I think I can get at them ok assuming that the bolts screw into threads on the sub frame and not separate bolts ? Any guida...
- Fri May 10, 2013 9:07 pm
- Forum: Problems / Questions
- Topic: 1.5DCI injectors-are they coded.?
- Replies: 2
- Views: 2663
Re: 1.5DCI injectors-are they coded.?
Hi there,
Yes they are coded to the ecu, as far as i know the codes on them are like calibration codes etc and the ecu needs to know them .
Yes they are coded to the ecu, as far as i know the codes on them are like calibration codes etc and the ecu needs to know them .