Search found 671 matches

by ChrisM
Fri May 17, 2019 8:40 pm
Forum: Megane CC
Topic: Megane CC boot lid
Replies: 1
Views: 63

Re: Megane CC boot lid

Where the rear number plate is, just above you have the number plate lamps in the middle of them is a rubber covered button (oblong and black rubber) press it it's a micro switch and electrically pops the latch, if I remember rightly the button on the card just unlocks it but doesn't pop it, if it d...
by ChrisM
Wed May 15, 2019 10:30 pm
Forum: Megane CC
Topic: best HIDs?
Replies: 4
Views: 929

Re: best HIDs?

Wouldn't bother. Chances are you will be pulled up on not for them same with after market LESs the light patterns are wrong so they fail on the headlamp section plus with hids you are supose to have headlamp washers fitted and working if not it's a fail. They are getting quite strict on them now. Do...
by ChrisM
Mon Feb 11, 2019 11:26 pm
Forum: Megane CC
Topic: How to remove the letters megane
Replies: 7
Views: 383

Re: How to remove the letters megane

You should get hold of a scenic badge ditch all the letters bar the 2 C,s and stick them under the diamond of doom badge so instead of reading MEGANE it will read simply CC.
Looks rather good.
by ChrisM
Tue Jan 29, 2019 11:46 pm
Forum: Megane III
Topic: heater
Replies: 5
Views: 366

Re: heater

Generally this will be fan motor Resistor stops fan working on all but full speed when power is straight through. Unless it has burnt wires somewhat common in the mk2 I believe it was something to do with the earth wire. If previous owner has been in there clearly they have not fixed it. So to me if...
by ChrisM
Tue Jan 08, 2019 7:47 pm
Forum: Megane CC
Topic: MK3 cc boot lid
Replies: 3
Views: 283

Re: MK3 cc boot lid

Hi Seano The silver trims you are looking at at the window seal trims i think the check strap is the black or silver flat rod inbetween the door hinges it controls how far the door opens and when it goes you will know about it every time you open and close the door it makes a good awful cracking sou...
by ChrisM
Sat Dec 01, 2018 12:20 am
Forum: Megane CC
Topic: Meg II CC Ownership Costs
Replies: 5
Views: 610

Re: Meg II CC Ownership Costs

Probably right about egr, I found my mk2 easy to clog up and a good low geared blast produced quite a black cloud the mk2 was also quite renowned for turbo lag, I had my mk2 mapped and it took a bit of lag out but still a massive pain. The mk3 hasn't got that "I'm not going" feel it's away...
by ChrisM
Wed Nov 28, 2018 9:12 pm
Forum: Megane CC
Topic: MK3 cc boot lid
Replies: 3
Views: 283

Re: MK3 cc boot lid

Have you tried ebay on a search for breaking megane convertible and sift through the cars..... Good luck though there arnt many around less than you think especially in scrap yards i tried for weeks to get a door check strap for mine with no luck got it sent from Germany in the end at £32. What do y...
by ChrisM
Thu Nov 15, 2018 12:00 am
Forum: Megane CC
Topic: Meg II CC Ownership Costs
Replies: 5
Views: 610

Re: Meg II CC Ownership Costs

Well the differance!!!!!! Same engine as my mk2 1.9dci Plus! Its pick up is a lot quicker, pulls out of junctions much faster. Better hand brake the airplane throttle type changed to a normal one. Bulbs on front end easy to change no bumper removal Better side window to roof seals instead of the mk2...
by ChrisM
Tue Nov 13, 2018 10:55 pm
Forum: Megane CC
Topic: Meg II CC Ownership Costs
Replies: 5
Views: 610

Re: Meg II CC Ownership Costs

3 good tips after owning my mk2 for 7 years and 150k 1) turn off auto headlamps my blew quite a few headlamp bulbs until I did this.view 2) purchase some krytox from your nearest VW dealer, this is the lube they use for the eos, cost you about £32 for a small bottle but well worth it.... It lubes an...
by ChrisM
Fri Sep 14, 2018 7:47 pm
Forum: Megane CC
Topic: Front Wing
Replies: 3
Views: 850

Re: Front Wing

Don't think front end bodywork is different at all i think they share the same wings, bonnet and bumpers with the rest of the Megan e range. Lots of owners of CC out me g RS front bumpers on as they fit but the rears won't . Dash clocks, mirrors, gear lever, steer wheel, hand brake, glove box raduo/...
by ChrisM
Tue Jul 03, 2018 10:59 pm
Forum: Megane CC
Topic: Rear window Temic issues
Replies: 5
Views: 1018

Re: Rear window Temic issues

Sorry that's a new one on me, did it work? I would rather doubt it you don't even have to reset the rear windows off the button like you do with the fronts so can't see holding a button up will do anything for the rears. Plus if this was so, the repair services would not ask which side it is (not th...
by ChrisM
Tue Jun 26, 2018 9:52 pm
Forum: Megane CC
Topic: Rear window Temic issues
Replies: 5
Views: 1018

Re: Rear window Temic issues

I had this from an ebay repair service.
I mounted my motor on the other side of the regulator, so it pulled in the right direction looked a bit odd but it went in ok and worked perfectly... :driving
by ChrisM
Wed May 30, 2018 10:29 pm
Forum: Megane III
Topic: Megane mk3 2009 mpg issues
Replies: 1
Views: 408

Re: Megane mk3 2009 mpg issues

Anything electrical you run will alter mpg lights, heated screen and heater blower being the worst, if you have altered you AC settings you will more than likely find that's the issue. AC is a big sap on mpg. If it has been like this since service did they adjust your hand brake of so could be bindi...
by ChrisM
Wed May 09, 2018 11:01 pm
Forum: Megane III
Topic: C C Brakes.
Replies: 0
Views: 270

C C Brakes.

:-( OMG 4 hours to clean up, new pads and lube rear calipers and replace front discs and pads..... None of the wheels would come off, had to belt them with a rubber malet for about 15 mins per corner so that kind of set the mood for the job, but rear calipers came off ok but the pads wouldn't move h...
by ChrisM
Wed May 09, 2018 10:21 pm
Forum: Megane CC
Topic: Ball Joint Size
Replies: 1
Views: 562

Re: Ball Joint Size

My last c c was an 04 and that was 18mm however it was a 1.9 diesel, I seem to remember being told the 16mm joints where the very early ones, I think I measured the exposed threads on the ball joint, it shouldn't be hard to determine the correct size 2mm is quite a jump.just make sure you return unj...

Go to advanced search